Wednesday, June 27, 2018

How to Install Windows 10 Complete


Tutorial that I will share this time on how to install (reset) windows 10. As you know that windows 10, Microsoft's operating system is inviting special attention for computer users.

Many of them are upgrading from their old operating system to windows 10. It is perfectly natural, considering the interface of windows 10 is very elegant and cool.

Display windows 10 is a blend of windows 7 and windows 8. You need to know also, how to install it is almost similar to how to install windows 8. My advice, read the tutorial well until it runs out later there will be no problem when the installation process of windows 10 .

Before installing windows 10 operating system, there are some things you need to consider, including as follows:
  • Prepare DVD installer windows 10 his first well, because this tutorial using DVD for installation media. 
  • To boot first from DVD, please first set boot device priority in BIOS menu.
  • If the installed laptop, plug the charger immediately, do not let the battery runs out time to install.
  • As usual, prepare some snacks or can also listen to music, because the installation process of windows 10 long enough. Installation process for about half an hour and half hour was very long for me, hehehe install casual only while nibbling.
How to setup BIOS to boot from DVD?

As I've said before, you'll need BIOS settings to boot the first time from DVD. Because the default computer / laptop boot first from HDD, then you should replace it in the following way:

1. Turn on or restart your computer / laptop. After that, press the DEL (Delete) button repeatedly until the BIOS display as shown below. Oh yah, not all computers / laptops use the DEL key to enter the BIOS menu, there are some of the most commonly used buttons like F1, F2, or Fn + F2 depending on the manufacturer. Next move to Boot tab using ◄ ► button.

2. As you can see that Hard Drive or HDD is at the top. This indicates that the first boot is done from the HDD.

3. For booting the first time from DVD, please select CD-ROM Drive then slide using + / - button to be in the top position as shown in the following figure.

4. Do not forget to insert the DVD installer windows 10 into DVDROM, then save the results of your BIOS settings earlier by pressing the F10 key, then select Yes.

Steps to install windows 10

Once you have BIOS settings to boot the first time from DVD, it's time you do the installation of windows 10. Check out the following steps to install windows 10:

1. Press any key to start windows installation 10. Suppose you are confronted with a display like this in the middle of the installation process, do not press any button yes, as you will be taken back to the initial installation process if doing so.

2. Select Indonesian (Indonesia) in Time and currency format, for others such as Language to install and Keyboard or input method leave default, no need to be replaced.

3. Next select Install now.

4. Then tick I accept the license terms, then select Next to continue.

5. In the following steps, please select Custom: Install Windows only (advanced).

6. Suppose you want to re-install and upgrade / downgrade from your old windows operating system to windows 10, just delete Drive 0 Partition 2 (C: partition :) and Drive 0 Partition 1: System Reserved, later automatically, both partitions you delete it to Unallocated Space (unpartitioned).

Well, next please create a new partition again and make Drive 0 Partition 2 as the location of the installation, then select Next to continue. That way, the data on other partitions remain secure (not deleted). More details, see the following gif images (If you use your phone while reading this tutorial, make sure you use Chrome or Mozilla browser to move the gif image perfectly):

7. As you can see in the following picture that the HDD space is still empty (Unallocated Space). For that, you have to partition it. For the number of partitions, can be 2 or more, as you wish.

8. Please select Drive 0 Unallocated Space> New, specify the size of the partition, then select Apply. The size is not too much and not too little too. Suppose your HDD size is 320GB / 500GB, give 100GB size is enough, because the first partition you created this is a system partition (C partition :). 

9. Select OK to create the system reserved partition.

10. Please create 1 or more partitions in the same way as in step 8.

11. As you can see in the following picture, I just created 2 main partitions. Next select Drive 0 Partition 2 for the installation location (do not place it on another partition yes), then select Next.

12. Installation process is running. This process takes about 30 minutes, just wait while eating chips. Oh yes, later your computer / laptop will restart itself repeatedly, so do not worry, because it is part of the installation process of windows 10.

13. Please enter your product key windows 10, then Next. If you do not have one, please select Do this later. You can activate your windows 10 later.

14. Next select Use Express settings.

15. Select I own it.

16. On this page you are asked to login your microsoft account. You can do it later, so choose Skip this step.

17. Please enter your computer name and password if necessary (it would be nice to give a password so not just anyone can access your computer / laptop). Fill in a word or phrase that helps you remember your password in the Password hint field.

18. This process does not take much time, just wait a while until you are taken to your desktop.

19. And taddaaah, installation of windows 10 succeed! Here's the desktop display on windows 10 is cool and interesting.

Well, hopefully you managed to install windows 10.

No comments:

Post a Comment